Автоматическая вставка клина якоря
Базовая информация
Модель: ND-LSI-1W
Описание продукта
Эта автоматическая машина для вставки клина якоря используется для вставки клина в паз якоря, чтобы изолировать якорь. Машина может быть настроена в соответствии с различными требованиями заказчика.
Технический параметр клиновидного станка
Outside Dimension |
910*880*1300(L*W*H)mm |
Equipment Weight |
250 Kg |
Motor Power |
0.75 Kw |
Work Voltage |
380 VAC |
Work Air Pressure |
0.4-0.6 hMp |
Manufacturing Product |
Motor Rotor Insulated Paper |
Rotor O.D. Range |
φ20-φ55 |
Length of Insulation Paper |
15-60 mm Adjustable |
(MAX) Width of wedge |
25 mm |
Rotor Slot number |
8-24 slots |
Work procedure |
Feeding-install fixture-plug in discharge |
Fixture |
Pneumatic Mechanical Fixture |
Feeding form |
Automatic |
Lubricant form |
Grease lubrication |
Ротор сделан на этой машине
Неисправности и устранение неисправностей
Malfunction |
Check |
A.Equipment not run even press start button
|
n Power and air supply |
n Make sure all input signal from sensor are correct, travel switch (X10) is pressed, no signal from counter sensor (X2), push bar protector (X7) and no paper sensor(x6) and full feeding (X4). Also, there is signal from the mechanic hand (X0) and magnetic sensor (X1) of small cylinder. |
|
n Brake is power off or not |
|
n The feeding sensor(X3) should have signal if there is rotor on the guide way. |
|
n Check cylinder and air pipe, make sure the pressure is between 0.4 and 0.6MPa |
|
B. Fail to feed paper |
n Check whether the paper is jammed in the feeding or discharging part, whether the upper press wheel is down pressed |
C. No action or improper action in big cylinder |
n Make sure the air pressure is 0.4 -0.6MPa |
n Check whether the magnetic valve is functional. |
|
n Adjust the release valve of feeding cylinder to 0.3 Mpa |
|
D. Incorrect work indexing |
n Adjust indexing screw |
E. No action in small cylinder |
n Check whether the mechanical valve is down pressed. |
F. The position is not correct after reset |
n Adjust the counter sensor screw and make sure it is on the right position after reset. |
G. Paper jam
|
n If it was blocked in the forming tooling, the equipment would stop because of the protective switch on duty. If it was blocked behind the upper press wheel, press the stop button, now the mechanical hand still hold the rotors, press the single/automatic button to adjust it to manual, the mechanical hand will release the rotor, then take out the paper, and reset, adjust the button to automatic, and start the equipment. |
Уведомление перед операцией
(1) Подтвердите перевозочную базу в упаковочном листе после распаковки и проверьте, не повреждены ли запчасти при транспортировке или нет. Он может быть использован только после установки и отладки нашим специалистом.
(2) Для обеспечения нормальной работы и обеспечения срока службы входное напряжение должно составлять 380 В переменного тока (допуск +/- 10%), а давление воздуха должно составлять от 0,4 до 0,6 Мп.
(3) Требуется надежная защита заземления.
(4) Не открывайте дверь или защитный кожух, когда машина работает или частично останавливается, не кладите руку или другую часть тела в машину.
(5) Обратите внимание на работу машины, немедленно остановите ее, если обнаружите какие-либо ненормальные условия. Только неисправность устранена, можно ли снова запустить машину.
(6) Переключатель должен быть установлен в состояние одиночного действия при проверке или обслуживании оборудования, и питание должно быть отключено.
Группа Продуктов : Машина для производства арматуры > Клин вставки машины